JBL Flip 4 behuizing vervanging

Geschreven door: Philip Pang
  • Reacties: 19
JBL Flip 4 behuizing vervanging

Moeilijkheid

Eenvoudig

Stappen

2

Tijd vereist

10 minuten

Inleiding

In deze handleiding wordt beschreven hoe u de behuizing en het rubberen van de luidspreker verwijdert. Deze gids markeert ook de eerste stappen om toegang te krijgen tot de batterij, luidsprekers, printplaten, enz. van de JBL Flip 4.

  1. TPdTjBXgaNNyAUQE
    TPdTjBXgaNNyAUQE
    uyxjyBvlQ5EvE4JM
    SXsnMdYGMSiQt6TY

    • Steek het plastic openingsgereedschap in de spleet tussen het deksel en de rubberen rug met de aan/uit knop.

    • Wrik de behuizing los, te beginnen met de zijkant zonder de volume- en bluetooth-knoppen.

    • Bij het loswrikken van de behuizing maken de zes clips (drie langs elke kant van de rubberen rug) die de hoes aan de luidspreker bevestigen klikkende geluiden.

    • Pas op dat u de clips aan de kant van de knoppen niet beschadigt, wrik voorzichtig open.

    • Trek het deksel eraf met uw duimen.

    Important suggested edit to these instructions - make sure to pry off clips/ridges from BOTH sides before attempting removal of the cover.

    I interpreted these instructions as saying you only needed to pry clips from one side - then peel off cover. Doing this broke a clip from the other side. Bummer. I'd like others to avoid that.

    k9612 -

    If you do break a clip - save it. They are relatively easy to glue back into the cover.

    k9612 -

    My Flip4 had a single long clip on the non-button side that ran the entire length of the rubber spine. The other side (with play/ vol buttons) had three seperate clips (middle and both sides) as mentioned above.

    takentrashout -

    What if my speaker battery dies very fast and makes weird crackling noise, is it counted as faulty battery?

    Jayden Koh -

    Yes. I first thought one of the drivers was defective.

    Paul Sommer -

    What was the fix in the end ?

    Jack Mulcahy -

    I used the flared edge of a metal measuring spoon handle since I didn’t have an opening tool. Worked great! Replacement battery from iFixit is on order. Thanks for the guide!

    Greg -

    My battery was glued. Tried it anyway to remove. Battery exploded!!!!

    Don't go on if the battery is glued.

    darthvader007 -

  2. MqSuoCcPNBeHtZpb
    MqSuoCcPNBeHtZpb
    bRHK1IRZthrIHwUj
    YFp1hjI2RBYUSP5B

    • Verwijder vier 13 mm JIS #0-schroeven waarmee de rubberen rug aan de luidspreker is bevestigd, aan beide zijden van de binnenkant van de luidspreker.

    • Gebruik het plastic openingsgereedschap om de clips los te maken die het centrale deel van de rubberen rug vasthouden.

    • Wrik het ene uiteinde van de rubberen rug weg met je duimen en deze zou dan los moeten komen.

    • Het loswrikken van de rubberen rug wat moeilijk gaan.

    • De speakers zijn sterke magneten. Houd ze uit de buurt van andere gevoelige elektronica.

    Suggested Edit : Be careful when removing the screws that they don't get attracted to the speaker (magnet). They can scratch the speaker.

    k9612 -

    Note : screws don't need to be removed from their “channel” (it’s quite difficult). Just unscrew fully and leave in channel.

    k9612 -

    Note or precaution: Place a piece of cardboard over the speaker or use a plastic/rubber/nonmetalic handled screwdriver when loosening/removing the 13 mm screws. The speaker magnets are so powerful that the end of my metal jewelers phillips screwdriver was pulled into the speaker, tearing the plastic/rubber cone. I destroyed two speakers in the process of replacing the battery. Had to buy the speakers from JBL ($16 each).

    Clark Brown -

    The rubber spine was fixed with glue strips.

    Jaider -

    I have 2 Flip 4's bought approx. a year apart. The older speaker was exactly as described here. The newer speaker does not have the 5 end screws, instead it has a twist to lock end plate. Make sure the top screws that secured the rubber end are removed, as these will prevent end cap twisting. I used rubber gloves to get a grip and twist end cap counter-clockwise to unlock. I found that if you grip end cap too tight it makes it even harder to twist off. Someone may find a better solution, like prising the tags around circumference, but be warned these look flimsy.

    Phil -

    Great guide. Only problem is that the battery on mine was in a neoprene sheath and had swollen. It was a bit of a problem to get out. There didn’t seem to be room to fit something to push it out without damaging wires or the motherboard. At the risk of a fire, I worked it back and forth and pulled with a pair of needle nose pliers. Yes there were sparks and some smoke. I did it outside and knew I was risking the whole thing catching on fire. Luckily it went ok.

    Q Switch -

    Great guide! I have a model with the twist-off caps (not 5 screws) with helpful, though subtle, lock/unlock icons on the plastic. Only other problem was replacing the white neoprene battery retainer cover (2 screws). One screw slipped off my screwdriver and fell into the unit - probably stuck to a speaker magnet now. But it doesn't seem to be affecting the sound. iFixit is the best!!

    Jen Morris -

    Una duda tienen la tapa que lleva al principio la bici en la parte de afuera

    Alexis Jesus -

    on the version w/o the five screws: Make sure that you push the lid at the cap where it says “R”to the outside far enough to be able to turn off the cap.

    The Beginner -

    In my case the screws where very tight and i couldnt access them very nice. i had to remove the speakers to get a better angle

    Melvin -

Conclusie

Volg deze instructies in omgekeerde volgorde om uw apparaat weer in elkaar te zetten.

Auteur

Philip Pang

Lid sinds: 08/10/18

1356 Reputatie

Een commentaar

教程不难， 难的是哪里可以买到配件。

Toki -